1. Cut a piece of card to measure 5.75" x 4.25". Using thin strips of cardstock divide the card off into quadrants . You can choose where they go but just make sure you do not make a cross or an X with them.They need to be off set as shown below.
2. Tip. All of the cards I have seen made, tell you to use either a tape runner/wet glue across the front of the piece of card or to apply a sheet of sticky adhesive to cover the entire card. This can be quite messy as you try to work around the card and not get your fingers or the sleeve of your cardigan stuck! My solution is to apply double sided tape only to the strips of paper you are going to be using. I attach strips of d.s tape to the wrong side of the paper I am going to use before I cut my strips. This way I can lay the strips down to make sure that they will not only fit but also that I am happy with the paper design. Only then do I go ahead remove the backing on the strip and adhere down.
4.When you have completed one section turn over and trim away the excess leaving a small margin.
5. Move onto the next section and complete as above trimming the excess away as you go.
6. Continue to move round the card
6. When each section has been completed make your final trim and use your panel to decorate your card base as required.
7. Here is my completed card.
3 Bar Herringbone
2. Place 3 strips of your chosen papers diagonally across the top of the card leaving a small even space in between. (This is where my tip in Version I really comes in to play with using d.s. tape on back of strips only).1. Cut a piece of card to measure 5" x 6". Cut your card strips half in wide. (0.5"). Washi tape works well for this particular design as well.
3. Infil the top section of card as shown below.
4. Using your middle 3 papers as your guide slightly off set 3 strips below the 3 bar panel and use design papers in a different order otherwise you will just end up with stripes going diagonally down the paper.
6. Trim around the edges and finish your card as required.
7. Here is my completed card.
1. Cut a piece of card to measure 5.5" x 6". This time you need to cut 7 squares that measure 1.5" x1.5". The design looks particularly pleasing if you just use two different coordinating papers in the same colour. (I used 2 papers from the same paper pack.) One square remains intact. Cut the other 6 squares in half to give you the long panels. Start off by placing the one whole square on the diagonal with both points right on the edge of the card as shown below.
4. Once you are happy with the over all design adhere down and complete your card as required.
4. Here is my completed card.
1. Cut a piece of card to measure 9" x 6". Score and fold at 3" and 6" on the long side to make a trifold shape.. Divide each of the three panels up at 1.5", 4.5" and 7.5" Draw a pencil line from top to bottom at these marks. Dot not fold on these marks.
. On the left hand edge make a pencil dot at 1",2",3",4",5" down the page. Repeat on the pencil lines and the 2 scored lines across the length. n.b I have only showed you the first panel. Now from the top left of panel down to the 1"mark on the first pencil line draw in a line to join up. Then repeat at the top right side down to the 1" mark to make a V shape. Continue down to the bottom of the page.
. Repeat on panels 2 and 3.These will be your guide lines for placing your herringbone pattern.
5. Now you can start to create your pattern. Pre cut your strips using the method I have stated in Version I above. I have cut my strips to be .5" (half an inch). Decide on your pattern and start to cut and stick the design paper in place as shown below.
. Continue down the first line.
. Using your strips in the same order complete the next line which creates the complete herringbone design.
. Now it is at this juncture I am going to say "Do not do as I do, do as I say". If you are going to use a striped pattern paper when you cut your strips you need to reverse the paper each time you cut a strip off other wise the below happens!!
. Complete your card as required.
Random Broken Herringbone.
1.This is a variation of the panel above.To create cut a piece of coloured cardstock to measure 5" x 5". Score at 1",2",3" and 4" across the top and then turn cardstock over so that the ridges of the score lines are uppermost.2.Here I am showing on white card( so that it shows up) to create various depths of each coloured design paper that you use. You want them to be random. Remember (as above) to reverse how you cut your strips to get the herringbone effect.
3.Here is my collection of strips that I have marked on the reverse and adhered ds. tape to before cutting.
4. Create your pattern across the card. I started with the brown spotted design paper top right (as you look at the picture) and then infilled above and below on that single panel working across the paper to the left of picture. In order for the pattern to stand out it does need at least one line to be the same pattern across. They do not all have to be the same depth. Here I have three lines across the cardstock using the same design paper. The pale cream with the flower design is all the same depth at top of page. The next continuous line (just over half way down) uses the brown spotted paper with one panel cut different. Again the last line right at the bottom using the pale cream with the flowers has one panel a different depth. It makes a really striking but at the same time subtle designl. The panel is completely flat but visually looks 3D.4. Complete your card as required.